Charge Controller
EPEVER Tracer1210AN 10A MPPT Charge Controller
Brand:EPEVER
Check Current Price & Availability →Affiliate disclosure: This link is an affiliate link. SunPowerLogic may earn a commission from qualifying purchases at no additional cost to you.
Product Overview
EPEVER Tracer1210AN 10A MPPT Charge Controller is a charge controller from EPEVER tracked in the SunPowerLogic product catalog. Where specifications are listed, this page summarizes controller current rating of 10 A, controller type of MPPT, supported system voltage of 12 V, maximum pv input voltage of 100 V, additional specification note of 12V/24V auto; 100V max PV open circuit; negative ground; LCD display; gel/sealed/flooded/lithium/user battery profiles; MPPT tracking efficiency ≥99.5%; RS485 Modbus; max PV 130W @12V / 260W @24V per listing.
Charge controllers regulate solar input to protect batteries and match charging profiles. Current rating, supported system voltage, and maximum PV input voltage are the key compatibility checks when pairing with panels and battery banks.
Additional listing note: 12V/24V auto; 100V max PV open circuit; negative ground; LCD display; gel/sealed/flooded/lithium/user battery profiles; MPPT tracking efficiency ≥99.5%; RS485 Modbus; max PV 130W @12V / 260W @24V per listing.
SunPowerLogic does not replace professional electrical design. Confirm wiring, fusing, and local code requirements for your build.
Editor’s Verdict
EPEVER Tracer1210AN 10A lists 10A charge current, 12V/24V auto support, and 100V max PV input per the source listing. It scores 7/10 for small RV and marine auxiliary arrays where modest MPPT capacity and negative-ground wiring match the published specs.
Pros
- 10A MPPT with 100V max PV input per listing
- 12V/24V auto and negative ground noted
- Gel/sealed/flooded/lithium/user battery profiles listed
Cons
- Uses shared Tracer AN family manufacturer image
- 10A charge ceiling limits scaling to larger banks
- EPEVER brand hub not yet in SunPowerLogic
Specifications
- Controller current rating
- 10 A
- Controller type
- MPPT
- Supported system voltage
- 12 V
- Maximum PV input voltage
- 100 V
- Additional specification note
- 12V/24V auto; 100V max PV open circuit; negative ground; LCD display; gel/sealed/flooded/lithium/user battery profiles; MPPT tracking efficiency ≥99.5%; RS485 Modbus; max PV 130W @12V / 260W @24V per listing
Best For
Ideal use cases based on product category, published specifications, and setup references in the SunPowerLogic catalog. These are planning contexts—not guarantees of compatibility for every installation.
- Small 12V/24V solar setups with modest daily yield
- RV and marine auxiliary charging within 10A planning
- Entry EPEVER Tracer AN builds before stepping up amperage
Not Ideal For
Situations where another product type, capacity tier, or specification may be a better fit.
- Primary house banks needing 20A+ charge current
- Large PV arrays where 10A becomes the bottleneck
- Buyers needing higher-amperage Tracer AN controllers
Used in These Setups
No setups yet
Alternatives to Consider
Other catalog products flagged as alternatives during editorial review.
Related Products
Products from the same brand or product type, excluding this listing.
EPEVER MT50 Remote Meter
View Product →EPEVER Tracer2210AN 20A MPPT Charge Controller (MT50 Kit)
View Product →EPEVER Tracer2210AN G3 20A MPPT Charge Controller
View Product →EPEVER Tracer3210AN G3 30A MPPT Charge Controller (MT52 Kit)
View Product →EPEVER Tracer4210AN G3 40A MPPT Charge Controller (MT52 Kit)
View Product →
EPEVER WiFi Adapter (EPEVER-WiFi-2.4G-RJ45-D)
View Product →Frequently Asked Questions
Is the EPEVER Tracer1210AN 10A MPPT Charge Controller suitable for RV use?
RV suitability depends on whether this charge controller matches your voltage architecture, daily energy budget, and charging equipment. Listed controller current rating is 10 A. Compare your load list and recharge plan against the listed specifications rather than the product category alone.
Can it be used off-grid?
Off-grid use is possible when the charge controller is sized for your daily consumption and paired with appropriate charging and protection equipment. Listed controller current rating is 10 A. Whole-property off-grid loads often require system-level planning beyond a single component.
Is it compatible with solar?
Solar compatibility depends on matching panel output, charge equipment limits, and battery chemistry. Listed controller current rating is 10 A. Verify controller current, voltage limits, and connector types before connecting arrays.
Does it require an inverter?
Most charge controller products operate on the DC side of a system. AC appliances typically require a separate inverter sized for peak and surge loads unless another integrated power station handles conversion.
How do I choose the correct size?
Start with daily energy use in watt-hours, identify peak AC demand, and map those figures to the relevant specification for this product type—amp-hours and voltage for batteries, watts for solar and inverters, or controller current for charge equipment. SunPowerLogic setup examples and buying guides show the same planning method using documented assumptions.
What should I verify before buying the EPEVER Charge Controller?
Confirm merchant listing details, warranty terms, connector types, and installation constraints that are not captured in the catalog. Listed controller current rating is 10 A. Affiliate links, when present, lead to external retailers where current availability and pricing should be confirmed directly.
Product specifications on this page come from published listings tracked in the SunPowerLogic catalog. They are planning references, not professional electrical designs. Verify compatibility with your loads and installation before purchasing.